Y. Jin, E. Holzbecher, and P. Oberdorfer
A novel method for groundwater lowering, which can be applied at construction sites, for aquifer remediation measures or in open mining, is proposed. In contrast to conventional techniques, dewatering is achieved without water conveyance. In this paper the physical concept of the new technology, referred as single borehole pump & inject, is modeled using COMSOL Multiphysics. Two and three ...
R.Christensen, and U. Skov
A compression driver is a certain type of electrodynamic loudspeaker which has a phase plug with slits in front of the diaphragm. The slits are narrow enough that the so-called viscothermal effects are of significant importance. In this paper a 2D axisymmetric finite element model of a commercial compression driver is established where the vibroacoustic behavior can be evaluated. The ...
A. Rosell, and G. Persson
Volvo Aero Corporation, Trollhättan, Sweden
Chalmers University of Technology, Göteborg, Sweden
Interaction between the probe and a defect in eddy current non-destructive evaluation is studied. Evaluation of sensor signal response is the basis for the calculation. In this work a differential sensor is considered and the problem regarded here is problem 8 from the testing of electromagnetic analysis methods (TEAM) workshops. The truncation, referring to the position of the outer ...
Fluid-Structure Interaction Modeling for an Optimized Design of a Piezoelectric Energy Harvesting MEMS Generator
I. Kuehne, A. van der Linden, J. Seidel, M. Schreiter, L. Fromme, and A. Frey
Siemens AG, Corporate Research & Technologies, Munich, Germany
Comsol Multiphysics GmbH, Göttingen, Germany
This paper reports the design of a piezoelectric energy harvesting micro generator for an energy autonomous tire pressure monitoring wireless sensor node. For our design we use a piezoelectric MEMS generator approach without additional mass. The intrinsic mass of the cantilever is in the microgram region and the resulting acceleration forces are very small. The generator has a triangular ...
M. Goncalves, T. Makaryan, G. Papageorgiou, U. Herr, and O. Marti
Ulm University - Inst. of Experimental Physics, Ulm, Germany
Yerevan State University, Yerevan, Armenia
Ulm University - Institute of Micro and Nanomaterials, Ulm, Germany
Surface enhanced Raman scattering (SERS) investigations of silver and gold triangular nanoparticles reveal strong field enhancements at the corners of the particles. Though the measurements were done at wavelengths far from the surface-plasmon resonance of the particles, large field enhancements can be generated by near-field coupling between the triangular particles and smaller metal ...
Military University of Technology
The article presents the process of verification of the passive magnetic bearing by the Comsol Multiphysic program. There is shown construction of the radial passive magnetic bearing PMB60x85x20-5, which was designed in the Military University of Technology. The distribution of the magnetic flux density and the static characteristic of the bearing were estimated by the Comsol Multiphysic. The ...
B. Chinè , and M. Monno
Laboratorio MUSP, Macchine Utensili e Sistemi di Produzione, Piacenza, Italy and Instituto Tecnologico de Costa Rica, Cartago, Costa Rica
Politecnico di Milano, Dipartimento di Meccanica, Milano, Italy
Modeling and simulation softwares are very useful tools when we have to analyse and understand the different phenomena occurring during metal foams processing, because several simultaneous physical mechanisms have to be accounted for. In this work we use Comsol Multiphysics 4.2 to model a spherical hydrogen gas bubble expanding in aluminium liquid, initially at rest. The aim of the present ...
Optimization of a Multiphysic Device – A Comparison of a Finite-Element- and a Equation-based Simulation
M. Jungwirth, and B. Hansbauer
University of Applied Sciences
To avoid overheating and malfunction of an electrical system it is necessary to optimize the power-loss of each component. The power dissipation mostly depends on multiple physical effects and therefore optimization is not an easy task. In this paper we focus on the reduction of complexity employing a equation-based simulation and compare it with a Finite-Element (FE) simulation in the ...
L. Spicci, and M. Cati
The present paper describes the development of a full FEM model for linear array high performance 5MHz ultrasound imaging transducer. As a preliminary design, a mono dimensional electro-acoustical KLM model was realized, then the complete FEM was developed and optimized. The optimized transducer was manufactured, so that agreement between transducer measured performances and simulation results ...
M. Herlitschke, M. Blasl, and F. Costache
Fraunhofer Institute for Photonic Microsystems
3D FEM simulation of millimeter-scale, complex electro-optically induced waveguide based devices demands the use of grids with more than several million nodes. Hence the simulation could take substantial time and require large amounts of available memory. This paper presents a computation algorithm based on the conversion of an initial 3D waveguide structure into an analogous 2D structure, ...