Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Different results using Mixture model for 5.4 version and 5.2a version

Please login with a confirmed email address before reporting spam

I am using Mixture to run for lubrication flow in journal bearing with cavitation. It is very interesting that when I used 5.2a version, I can get the correct answer. When I used 5.4 version, the result is simply wrong. I believe that 5.4 version has a problem in mixture model.


6 Replies Last Post 2019年10月21日 GMT-4 21:09

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 2019年9月10日 GMT-4 06:48
Updated: 5 years ago 2019年9月10日 GMT-4 06:48

I have noticed that since 5.4, the eqations for mixture model have been different from the earlier version. Perhaps there is some issues involved in there. Don't have any problem for bubbly flow model.

I have noticed that since 5.4, the eqations for mixture model have been different from the earlier version. Perhaps there is some issues involved in there. Don't have any problem for bubbly flow model.

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 2019年9月10日 GMT-4 09:07

I have found that it has something to do with the numerical diffusion. Still looking for appropriate set.

I have found that it has something to do with the numerical diffusion. Still looking for appropriate set.

Mats Nigam COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 2019年9月11日 GMT-4 04:52

Dear Shiuh-Hwa, The formulation for the mixture model was changed in v5.4. It is now formulated in terms of the volume-averaged velocity instead of the mass-averaged velocity used in prior versions. If you can share your model, we can check that it's consistently set up. Best regards, Mats Nigam

Dear Shiuh-Hwa, The formulation for the mixture model was changed in v5.4. It is now formulated in terms of the volume-averaged velocity instead of the mass-averaged velocity used in prior versions. If you can share your model, we can check that it's consistently set up. Best regards, Mats Nigam

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 2019年10月14日 GMT-4 02:31

Dear Shiuh-Hwa, Did you solve your problem?

Dear Shiuh-Hwa, Did you solve your problem?

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 2019年10月14日 GMT-4 03:28
Updated: 5 years ago 2019年10月14日 GMT-4 03:31

Dear Mats Nigam and Mohammad Faizan

I did solve the problem. As I said, the numerical diffusion has to be adjusted. I have to lower it down an order for my case.

Plus, the turning parameter in thin-film model (tffs) has to be lowered down from 5, suggested by the turtorial example, to 0.5.

Dear Mats Nigam and Mohammad Faizan I did solve the problem. As I said, the numerical diffusion has to be adjusted. I have to lower it down an order for my case. Plus, the turning parameter in thin-film model (tffs) has to be lowered down from 5, suggested by the turtorial example, to 0.5.

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 2019年10月21日 GMT-4 21:09

I need to back off quite a bit. For the mixture model, I haven'r resolve the problem yet. I have read the wrong file, which is Bubbly Flow model.

I need to back off quite a bit. For the mixture model, I haven'r resolve the problem yet. I have read the wrong file, which is Bubbly Flow model.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.