Simulating an RF MEMS Switch
Lexi Carver | January 7, 2014
An RF MEMS switch is an electromechanical component found in RF systems. It usually consists of a micromechanical bridge or cantilever, a substrate, and an electrode or dielectric layer. These devices can switch at RF frequencies and tend to have high isolation, i.e. power loss when the switch turns off; low insertion loss (loss of signal power when the switch is on), and extremely low (almost zero!) power consumption. Let’s take a look at how you can use COMSOL Multiphysics to simulate an RF MEMS switch.
Analyzing Capacitance and Contact Forces
The RF MEMS Switch model, available in the COMSOL Model Gallery, shows how to simulate and analyze the contact forces and capacitance changes that occur during operation of the switch. The switch geometry contains a thin micromechanical bridge made of a square plate of polysilicon. The plate is suspended 0.9 µm above a silicon nitride film that is 0.1 µm thick. Underneath the film is a grounded counter-electrode.
The main goal of this simulation is to approximate the time it takes the bridge to make contact with the film, and to compute the capacitance of the switch when the bridge is fully pulled in. The COMSOL geometry contains the plate, including the flexures (fixed tabs at the corners that anchor it), and the nitride film is modeled using a function that varies the dielectric constant across the gap between the bridge and the film. As the bridge presses into the film, the mesh — which is used to model the gap — compresses into the nitride layer.
Since the switch is symmetrical, it’s only necessary to model one quadrant of the geometry:
Geometry of the RF MEMS switch as modeled in COMSOL Multiphysics together
with the MEMS Module.
In a switch like this, the bridge responds to an applied electric potential and voltage by pulling down on the film. As the voltage increases, the bridge bends closer and closer to the film, causing the capacitance of the device to increase dramatically. We simulate the contact between the bridge and the film using a technique called the penalty method — a solving algorithm that helps describe the forces occurring in the system.
RF MEMS Switch Model
We want to understand how the bridge bends as it closes the gap, and to know its capacitance in the two configurations. The figure below shows a schematic of the switch operation and the model geometry in the “off” and “on” states.
Left, schematic showing the switch operation; right, displacement of the switch when pulled in (color)
as well as the original position of the switch in the off state (wireframe).
The switch is placed between the device and an AC source. When the switch is off (top left in the figure above), its small capacitance appears like an open circuit to the AC signal. When a DC voltage is applied in addition to the AC voltage, the silicon is pulled down onto the isolating nitride film and the switch turns on (bottom left in the figure above). In this configuration, the capacitance is much larger and the switch appears like a closed circuit to the AC signal.
We can model the surface of the nitride film as a nonlinear spring — where the “stiffness” is low when there is no contact between the bridge and the film, but increases as the bridge moves closer to the film and the gap narrows. Knowing, or closely estimating, this spring constant makes it possible to calculate the voltage that causes the bridge to pull in and contact the film; this is called the pull-in voltage.
Here’s what happens to the capacitance as the bridge nears the film:
Plot of the capacitance of the switch over time, changing with the increase in voltage.
It remains fairly constant for the first 30 microseconds and then makes a sudden jump. At this point, most of the bridge is in contact with the film. The displacement here is 0.9 µm, so the bridge has fully closed the gap between them. At roughly the same time as this notable increase in capacitance, the displacement makes a similar leap:
Plot of the displacement over time.
It turns out that the capacitance changes more rapidly than the displacement, because of the non-uniform dielectric constant in the gap.
- Download the RF MEMS Switch model and step-by-step instructions for performing this simulation from the Model Gallery.
Conjugate Heat Transfer
- Certified Consultants 30
- Chemical 48
- COMSOL Now 136
- Conference 102
- Core Functionality 58
- Electrical 118
- Fluid 86
- Interfacing 36
- Mechanical 142
- Multipurpose 14
- Tips & Tricks 32
- Trending Topics 44
- User Perspectives 82
- Video 64